close

Best Metal Cutting Circular Saw Table Resources and Information Online for Metal Cutting Circular Saws




Home

What Do You Desire to Know About cutting metal?

Do you know how metal cutting with circular saws works? Doesn't it baffle your mind a little? Do you consider it a whole lot? Would you like to understand more than just the fundamental facts? Things like trivia and other intriguing bits of info? It is easy to find a variety of wonderful information concerning cutting currugated metal with a circular saw in this regularly updated website. Do not wait! Start clicking and reading now!

But to do so, it takes patience. You cannot cut it like wood. It takes me about ,,, I'd say 3 or 4 minutes to slowly cut a piece of 2" x 2" x 1/4" angle iron. If you force it or bind it at all, you with break the teeth and I am here to tell you, 40 pieces of tungsten flying off a saw all in a split second is not a good thing to be around. It's dang near like a grenade going off. I have had to dig metal out of my arms that were probably a quarter inch deep. These are relatively new to the market but I think they are fantastic. They are not cheap and a good quality one will set you back close to $500. Now if you plan on doing a lot of projects around the home, or you are a professional contractor, then just break out the credit card and get one. I did and am delighted that I made the investment.



A good jigsaw (my favorite is the Milwaukee with a nice speed control) and you can follow any line, even a straight rip cut. The higher end jig saws have very low vibrations and tend to make very controlable cuts. A straight rip through a 2x4 is very doable. One issue, the more expensive jig saws tend to have 1.25" stroke, so you either cut both sides at once (and jig saws are bad at this because blades flex) or you get a very short blade (or cut down one you have).

Below are Some Even more Info on Cutting Metal With A Circular Saw

Skill Saw Blade For Metal Roofing

Cutting metal is a more difficult task than cutting wood, and it's accomplished more by abrasion than by removing a relatively large amount of wood. You'll find the RPMs that those 7-1/4-inch blades spin create a lot of sparks (read: flying, flaming hot metal shards) and will wear the blade quickly (please note: for safety, always confirm the blade RPM rating is within the saw's RPM rating.) The metal cutting saw's design is specific to keep those shards collected or at least deflect them better than your standard circular saw will. Finally, but more generally, a traditional wood circular saw's open housing might not protect against metal shard buildup. Metal-cutting saws typically have a closed housing for that purpose.

A good jigsaw (my favorite is the Milwaukee with a nice speed control) and you can follow any line, even a straight rip cut. The higher end jig saws have very low vibrations and tend to make very controlable cuts. A straight rip through a 2x4 is very doable. One issue, the more expensive jig saws tend to have 1.25" stroke, so you either cut both sides at once (and jig saws are bad at this because blades flex) or you get a very short blade (or cut down one you have).

Below are Some More Info on Cutting Thin Metal With Circular Saw

When using a circular saw, you need to be sure you're using the correct blade for the material you are cutting. Not only will you need a different blade for cutting metal than you would for cutting wood, but a metal-cutting blade should not be used in the same saw as the type used for wood. This is because a wood-cutting circular saw has an open motor housing. While a metal-cutting saw has a collection bin to prevent metal chips from getting into the machine, a woodcutting saw isn't designed this way. If you do decide to use a wood saw on metal, only use a 7 1/4-inch blade and preferably a worm drive blade, which provides extra torque. Be aware that while most saw blades should be installed with the label visible, worm-drives are mounted on the opposite side.

Don't Be Satisfied With Less Than the Best Whenever It Comes to circular saw metal cutting.

In my post I was not suggesting a regular circular saw. I am not sure what the difference is between the link and a regular circular saw. Obviously a lot more shrouding around the blade. I have cut a lot of aluminum soffit using a regular circular saw with the blade in backwards but I would not try it on steel.

Yes you can, I agree with all of the above. But it throws a lot of sharp chips and sparks. So beware. There is a carbon saw that is designed for metal...wears as it cuts. will last 12 feet in 14ga sheet metal. When using a circular saw, you need to be sure you're using the correct blade for the material you are cutting. Not only will you need a different blade for cutting metal than you would for cutting wood, but a metal-cutting blade should not be used in the same saw as the type used for wood. This is because a wood-cutting circular saw has an open motor housing. While a metal-cutting saw has a collection bin to prevent metal chips from getting into the machine, a woodcutting saw isn't designed this way. If you do decide to use a wood saw on metal, only use a 7 1/4-inch blade and preferably a worm drive blade, which provides extra torque. Be aware that while most saw blades should be installed with the label visible, worm-drives are mounted on the opposite side.

Find out more about cutting metal with circular saws...

Did you find it helpful as well as simple to read? Did you find it as helpful as we did? It is preposterous that quite a few of the articles out there are so tough to understand. Understanding makes all of the difference in making a well timed decision and circular saw metal cutting is so vital to that you need the right info. And who has time to wait nowadays?


Previous Post     Next Post
You may also like these posts:
Best Circular Saw Blade To Cut Metal Door Resources and Information Online for Metal Cutting Circular Saws
Best Morse Metal Cutting Circular Saw Resources and Information Online for Metal Cutting Circular Saws
Best Dewalt Circular Saw Blade For Metal Resources and Information Online for Metal Cutting Circular Saws

Leave a Comment:



Copyright © Best Metal Cutting Circular Saw Table Resources and Information Online 2018